HiModel
2.4G 9-CHANNLE MICROLITE DSM2 RECEIVER W/ SATELLITE (JR/SPEKTRUM COMPATIBLE)
| ◆ Type | 9-Channel Full-Range DSM2 Receiver |
| ◆ Modulation | DSM2 |
| ◆ Band | 2.4GHz |
| ◆ Dimensions (W x Lx H) | 30 x 50 x 13mm |
| ◆ Weight | 19g |
| ◆ Voltage Range | 4-10v |
| ◆ Brown-Out Voltage | 4.0v (Always supply power above this voltage) |
| ◆ Antenna Length Main RX | 30mm (2) |
, , , , , , Specifications:, , , , , , , , , , , Wireless simulator interface(W.D.S.C), 1. Main receiver and satellite must connect., 2. Receiver must bind with transmitter first (AUX4 channel do not plug binding harness), 3. AUX3 is the (W.D.S.C) channel, connect with simulator line, 4. BIND channel and AUX4 channel plug the binding harness, 5. Apply power to the receiver with USD line or battery, 6. Turn transmitter on, now both LEDS keep light and simulator works, Binding Procedure, 1. Put the binding harness into connector location marked BIND. Next apply power to the receiver. Both receiver and Satellite LED's should illuminate., 2. To set fail-safe throttle and control surface positions, (minimum throttle and all control surfaces set to neutral is suggested). Press and hold the bind button of transmitter (LED will illuminate), Turn on the transmitter., 3. Receiver LED will change from rapid flashing to slow flashing and a few seconds later when bind is accomplished the LED of both satellite and main receiver will illuminate solid. All fail-safes should be programed correctly now., 4. Remove binding harness from the BIND channel. Restart the receiver by cycling it power off and turn on. All channels should function properly now. You may test fail-safe by holding sticks in corner, cycle transmitter on and off. Surfaces and throttle should return to your preset fail-safe positions., General Notes:, Only one bind procedure is required on a new receiver. Repetitive binding provides no extra security. Always remember to remove the binding harness after successful bind is completed., , ,
Features: JR/SPEKTRUM Compatible Key Features ◆ 9 channels ◆ Patent ...1 Reviews
HiModel
EZRUN-SC8 120A WATER PROOFING BRUSHLESS ESC FOR SHORT COURSE TRUCK WP-SC8
| 1.1 Output | Continuous 120A, burst 760A; |
| 1.2 Input | 6-12 cells NiMH/NiCd or 2-4S Lipo; |
| 1.3 BEC Output | * Note #1 |
| 1.4 Resistance | 0.0004 Ohm; |
| 1.5 Motor Supported | Sensorless Brushless Motor; |
| With 6 cells NiMH/NiCd or 2S Lipo | KV≤6000; |
| With 7-9 cells NiMH/NiCd or 3S Lipo | KV≤4000; |
| With 10-12 cells NiMH/NiCd or 4S Lipo | KV≤3000; |
| 1.7 Suitable Car | 1/10 4WD SCT, 1/8 2WD and 4WD buggy/SCT (Include TRAXXAS 1/10 SCT); |
| 1.8 Size | 59mm(L) * 38mm(W) * 34mm(H); |
| 1.9 Weight | 113g; |
| * Note #1 | The cooling fan of EZRUN-WP-SC8 is powered by the built-in BEC. |
, , , , , , Specifications:, , , , , , , , , , , Specification, 6V/3A (Switching mode);, 1.6 Suitable Brushless Motor:, Application suggestion:, 1. 1/8 scale SCT/Buggy all-weather sport racing, 2. 1/10 4WD SCT/Buggy/Truggy/Monster all-weather sport racing, , ,
Features: THIS IS THE NEW WATER PROOFING VERSION. Features 1 ...HiModel
EZRUN-SC10 70A SHORT COURSE ESC + 3655SL-3500KV MOTOR + PRO-CARD COMBO FOR 1/10 TRUCK
| EZRUN-SC10 ESC | Continuous current 70A, burst current 520A; |
| EZRUN-SC10 ESC | 6-9 cells NiMH/NiCd or 2-3S Lipo; |
| 1.3 BEC Output | Note1 |
| EZRUN-SC10 ESC | 6V/3A (Linear mode); |
| EZRUN-SC10 ESC | 0.0007 Ohm; |
| 1.5 Motor Supported | Sensorless Brushless Motor |
| With 6 cells NiMH/NiCd or 2S Lipo | KV≤6000; |
| With 7-9 cells NiMH/NiCd or 3S Lipo | KV≤4000; |
| EZRUN-SC10 ESC | 1/10th scale 2WD short course truck / buggy / monster; |
| 1.8 Size | 53.5mm(L) * 36mm(W) * 36mm(H). |
| EZRUN-SC10 ESC | 88g; |
| Note1 | The cooling fan of EZRUN-SC10 and EZRUN-SC8 is powered by the built-in BEC of 6V. |
, , , , , , Specifications:, , , , , , , , , , , 1.1 Output:, 1.2 Input:, 1.4 Resistance:, 1.6 Suitable Brushless Motor:, EZRUN-SC10 ESC:, 1.7 Suitable Car:, 1.9 Weight:, , ,
Features: 1 Integrated and compact design, very suitable for short ...HiModel
XERUN-60A BRUSHLESS ESC FOR 1/10 CAR/TRUCK (BLUE SPIRIT EDITION)
| Model | XERUN-60A-V2 |
| Cont./ Burst Current | 60A/360A |
| Resistance | 0.0006 ohm |
| Suitable Car | 1/10, 1/12 on-road & off-road, 1/8, 1/10 scale rock crawler |
| Suite motors | Sensored and sensorless Brushless Motors |
| Battery | 4-9 cells NiMH or 2-3 cells Li-Po |
| BEC Output | 5.75V@3A Built-in BEC |
| Dimension | 43mm(L) * 36mm(W) * 33mm(H) |
| Weight | 80g |
| Fan Working Voltage | 5V@0.16A, maximum 8V. (The fan gets the power supply directly from the battery) |
, , , , , , Specifications:, , , , , , , , , , , 5-6 NIMH or 2 Lipo ≥5.5T(on-road), ≥Suitable 8.5T(off-road), 8-9 NIMH or 3 Lipo ≥10.5T(on-road), ≥17.5T(off-road), , ,
Features: 【FEATURES】 ► Compatible with all sensorless brushless motors and ...HiModel
XERUN-120A-V2 BRUSHLESS ESC FOR 1/10 CAR/TRUCK (BLUE SPIRIT EDITION)
| Model | XERUN-120A-V2 |
| Cont./ Burst Current | 120A / 760A |
| Resistance | 0.0003 ohm |
| Suitable Car | 1/10, 1/12 on-road & off-road, 1/8, 1/10 scale rock crawler |
| Suite motor | Sensored and sensorless Brushless Motors |
| Battery | 4-9 cells NiMH or 2-3 cells Li-Po |
| BEC Output | 5.75V@3A Built-in BEC |
| Dimension | 43mm(L) * 36mm(W) * 33mm(H) |
| Fan Working Voltage | 5V@0.16A, maximum 8V. (The fan gets the power supply directly from the battery) |
, , , , , , Specifications:, , , , , , , , , , , 5-6 NIMH or 2 Lipo ≥3.5T(on-road), ≥5.5T(off-road), 8-9 NIMH or 3 Lipo ≥5.5T( on-road), ≥8.5T(off-road), Weight 105g, , ,
Features: 【FEATURES】 ► Compatible with all sensorless brushless motors and ...HiModel
XERUN-80A BRUSHLESS ESC FOR 1/8 CAR/TRUCK
| Model | XERUN-80A |
| Cont./ Burst Current | 80A / 380A |
| Resistance | 0.0006 ohm |
| Suitable Car | 1/8 on-road, off-road and monster RTR applications |
| Suitable motors | Sensored and sensorless Brushless Motors |
| Battery | 6-12 cells NiMH or 2-4 cells Li-Po |
| BEC Output | 5.75V@3A Switch mode built-in BEC |
| Dimension | 58mm(L) * 46.5mm(W) * 35mm(H) |
| Weight | 105g (Wires not included) |
| Cooling Fan Working Voltage | 5V, maximum 8V. (The fan gets the power supply from the built-in BEC) |
, , , , , , Specifications:, , , , , , , , , , , 【SPECIFICATIONS】, ≥6T, KV≤2400 (Works with 4S Lipo), , ,
Features: ► Compatible with all sensorless brushless motors and most ...HiModel
TORO 8 150A BRUSHLESS SPEED CONTROL FOR 1/8 CAR
| Input Power (Cells) | 2-6S LiPo |
| Brushless KV≤2400 | Up to 6S(25.2Volt), |
| Brushless KV>2400 | Up to 4s(16.8volt) |
| Continuous/Burst Current | 150 Amp / 950 Amp |
| Dimension | 48.8x57.8x35.8mm |
| Weight (Without wires) | 88g |
, , , , , , Specifications:, , , , , , , , , , , Speed control specifications:, Motor Limits, for 1/8 monster trucks and truggies, ideal for 1/8 buggies, , ,
Features: Controls, TORO 8 Fwd/Brk or Fwd/Brk/Rev Input Power (Cells) ...HiModel
WFT06II 2.4GHZ 6-CHANNEL RADIO SYSTEM
| Model | WFT06II |
| Use in | Airplane,Helicopter,Car,Boat |
| Band | 2.400-2.483GHz |
| Output Power | ≤100mW |
| Modulation | 2.4GHz DSSS(spread Spectrum)+Frequency Hopping |
| Memory | 8-model memory |
| Power | 3.7-6.0V ≤190mA |
| Transmitter programe language | English |
, , , , , , Specifications:, , , , , , , , , , , Transmitter stick mode: both mode 1 and mode 2 are available, mode 2 (throttle on left hand) will be sent by default. If you need mode 1, you can specify the stick mode in the Remark field on the last step when place the order., , ,
Features: THIS IS THE NEW WFT06II. ● Great choice for ...2 Reviews
HiModel
SPRINGRC 2.4GHZ 4 CHANNEL RADIO CONTROL SYSTEM TG461S TX & RX SET MODE 2
| Control System | Pulse width control |
| Control System | Pulse width control(PPM) |
| Outside the box | 520×300×260mm（L×W×H）、5PCS per carton、Net Weight-2658.5g、Gross weight-4739.5g |
, , , , , , Specifications:, , , , , , , , , , , Transmitter：SM-TG461S MODE 2, Transmission frequency：2.4G, Modulation：FSK, Radio Interface：SMA, Control system：4 Channel, Power Supply：8 AA Ni-MH/Alkaline batteries, Current： , Transmitter size：201X192X60(mm), Finetune Way：Mechanical trim, Receiver：SM-RG661, Receive frequency：2.4G, Operating voltage：4.8V ~ 6V, Receiver IF bandwidth：500KHz, Receive sensitivity：≤-100dBM, Current ： , Receive size：24.5X21.0X11.2(mm), product packaging ：Color Box Packing, Specifications：Inside The Box：226×205×99mm（L×W×H）、Net Weight-531.7g、Gross weight-796.7g, , ,
Features: 4 Channel 2.4G transmitter with 6 Channel 2.4G receiver ...HiModel
2.4GHZ 3-CHANNEL LED TRANSMITTER AND RECEIVER SET LED VERSION N-4Q
| ●TYPE | LED Edition N-4Q |
| ●Code format | PCM |
| ●Max transmitting power | 20dBm 200mA. |
| ●Max receiving sensitivity | -93dBm. |
| ●Working current at transmitting end | 200ma 秋300A. |
| ●Data transfer rate | 19200 bit/sec. |
, , , , , , Specifications:, , , , , , , , , , , Specifications:, ●Technology of DSSS (direct sequence spread spectrum) 2.4g radio transmission and receiving, ●Working frequency is the worldwide universal frequency band of ISM (industrial scientific and medical) free of charge, and the range is from 2.4 Ghz to 2.48 Ghz., ● Working current at receiving end: , * Plain carton packing., , ,
Features: THIS IS THE LED EDITION OF N-4Q RADIO. ● ...2 Reviews
HiModel
SPRINGRC 2.4GHZ 6-CHANNEL RADIO TX & RX TG661A SET MODE 2
| Type | TG661A |
| Stick mode | mode 2 (throttle on left hand) |
| Transmission system | FHSS (frequency hopping) |
| Power supply | C 9.6V to 12V (AA x 8) |
| Channel number | 6 channels |
, , , , , , Specifications:, , , , , , , , , , , Transmitter specification:, Frequency：2.4GHz-2.483GHz, Modulation：FSK, Channel count: 21, Trim type：electronic stepping, Receiver type：RG661A, Voltage：4.8--6V, Weight：5.2g, Size：34*21*14mm, *HINT: There are no knobs for VR(B)and VR(A) trims, they are designed to be adjusted with a screw driver, also the V-TAIL MIXING switch is also "hide" inside, and can only be moved by a tweezers or a thin rod, this design will avoid those settings are changed accidentally, also those settings normally not supposed to be adjusted frequently., , ,
Features: THIS IS THE NEW VERSION TG661A (A UPGRADING OF ...2 Reviews
HiModel
SPRINGRC 2.4GHZ 6-CHANNEL RADIO TX & RX SET TG661A MODE 1
| Type | TG661A |
| Stick mode | mode 1 (throttle on right hand) |
| Transmission system | FHSS (frequency hopping) |
| Power supply | C 9.6V to 12V (AA x 8) |
| Channel number | 6 channels |
, , , , , , Specifications:, , , , , , , , , , , Transmitter specification:, Frequency：2.4GHz-2.483GHz, Modulation：FSK, Channel count: 21, Trim type：electronic stepping, Receiver type：RG661A, Voltage：4.8--6V, Weight：5.2g, Size：34*21*14mm, *HINT: There are no knobs for VR(B)and VR(A) trims, they are designed to be adjusted with a screw driver, also the V-TAIL MIXING switch is also "hide" inside, and can only be moved by a tweezers or a thin rod, this design will avoid those settings are changed accidentally, also those settings normally not supposed to be adjusted frequently., , ,
Features: THIS IS THE NEW VERSION TG661A (A UPGRADING OF ...HiModel
SPRINGRC 2.4GHZ 4 CHANNEL RADIO CONTROL SYSTEM TG461S TX & RX SET MODE 1
| Control System | Pulse width control |
| Control System | Pulse width control(PPM) |
| Outside the box | 520×300×260mm（L×W×H）、5PCS per carton、Net Weight-2658.5g、Gross weight-4739.5g |
, , , , , , Specifications:, , , , , , , , , , , Transmitter：SM-TG461S MODE 1, Transmission frequency：2.4G, Modulation：FSK, Radio Interface：SMA, Control system：4 Channel, Power Supply：8 AA Ni-MH/Alkaline batteries, Current： , Transmitter size：201X192X60(mm), Finetune Way：Mechanical trim, Receiver：SM-RG661, Receive frequency：2.4G, Operating voltage：4.8V ~ 6V, Receiver IF bandwidth：500KHz, Receive sensitivity：≤-100dBM, Current ： , Receive size：24.5X21.0X11.2(mm), product packaging ：Color Box Packing, Specifications：Inside The Box：226×205×99mm（L×W×H）、Net Weight-531.7g、Gross weight-796.7g, , ,
Features: 4 Channel 2.4G transmitter with 6 Channel 2.4G receiver ...HiModel
WALKERA DEVO 12S 2.4G 12-CH RADIO SYSTEM W/TELEMETRY FUNCTION
| 1). Encoder | ARM micro computer system |
| 2). Frequency | 2.4Ghz |
| 3). Output power | -5dBm~20dBm |
| 4). Battery | 3.7V 3000mAh LiPo |
| 5). Stand-by time | 10h |
| Type | 2.4GHz 12 channels |
| Sensitivity | -105dbm |
| Frequency Interval | ≥ 4M |
| Weight | 15g |
| Dimension | 47X32X16mm |
, , , , , , Specifications:, , , , , , , , , , , DEVO-12 Specification:, DEVO-RX1202 Specification:, * Stick mode: both mode 1 and mode 2 are available, there are detailed instructions on how to change the stick mode in the instruction manual, customers can swap the stick mode by yourself if you receive a radio not in the preferred stick mode., , ,
Features: Features: 1). it provides rainbow,gem blue,skyblue,three backgrouds. 2). it ...5 Reviews
HiModel
SKYRC MULTI-FUNCTION WATT METER
| Voltage | 0-60V (*1), resolution 0.01V |
| Current | 0-100A peak (*2), resolution 0.01A |
| Power | 0-6000 W, resolution 0.1W |
| Charge | 0-65Ah, resolution 0.1mAh |
| Energy | 0-6554Wh, resolution 0.1KWh |
| Temperature | 0-150℃/ 32°F - 302°F |
| Auxiliary power | 4-60V |
| Dimensions | 51.3 x 42.9 x 13.7mm |
| Net weight | 42g/ 1.48oz |
| Display | 26.5 x 28.5mm LCD |
, , , , , , Specifications:, , , , , , , , , , , Note:, (*1) 0V minimum with auxiliary power, (*2) 50A continuous, 100A peak, assumes device's wire are in free air and attached to connections at or below temperature of 35 flow. 100A operation time depends on ambient temperature and wiring temperature., You can calibrate all values to zero by pressing 'SW' button for more than 3 seconds., , ,
Features: FEATURES Measures energy (Wh), charge (Ah), power (W), current ...